MICROLINE 320/390FBUser Manual (English) MICROLINE 320/390FB User Manual (English)
E – 9Connecting to the ComputerThese instructions are for the standard centronicsparallel interface.1. Make sure that both the printer and the compute
E – 10Installing the Ribbon Cartridge1. Set the headgap lever to the “R” position.2. Open the access cover.3. Slide the print head gently towards the
E – 115. Insert the flat end of the cartridge into the upperpart of the ribbon plate, then lower the front ofthe cartridge over the printhead until it
E – 12Important: Do not peel off the plastic film (ribbonmask) on the top of the cartridge. Do not stack theribbon cartridge sideways, it will cause p
E – 133. Push the paper lever to the continuous paperposition.4. Adjust the headgap lever on the left side of theprinter according to your paper thick
E – 14Note: In the positions above 5, the printer slows downto maintain print quality with thicker multipartforms.Note: “R” position indicates ribbon
E – 157. Open both of the pin-tractors covers.8. Lay down the continuous paper with printingface upwards on to the pin-tractors. Adjust thepaper so th
E – 16Note: The arrow icon (▼▼▼▼▼) on the scale and also thecentre of the diamond shaped hole indicate the centreof the first printed character.10. Sl
E – 1711. Close the table. The extension guide is notnecessary when using continuous paper. Pushit clockwise so that it folds under the sheetstacker.1
E – 18Loading Cut Sheet paper1. Check that the power is on.2. Check that the SEL lamp is off (printer off-line).If it is on push the SEL button to tur
E – 1EnglishTable of ContentsNote to Customers ... E-2Important Safety Instructions ... E-3Important Wi
E – 19Note: Unless you alter the standard margin settingusing the MENU MODE, the paper guide must beplaced correctly against the arrow icon: too big a
E – 20Setting the Top of FormYour printer can adjust the top of form (the first lineof the printing surface) by increments of 1/144 inch.This allows y
E – 213. Release the two buttons at the desired top ofform position. Press the TOF/QUIET buttonagain to fix the setting. It remains in the printer’sme
E – 222. Also, keep the printer 60 cm or more from thewall in order to store paper. These storagerequirements are necessary to avoid jammmg.Running a
E – 23Printing Demo Patterns1. First load the printer with the correct paper.2. Switch off the power to the printer.3. Choose the demo pattern you wan
E – 24Changing Menu SettingsTo change the menu settings follow these steps:1. Make sure that the printer is on line.2. Press the MODE/Exit button to p
E – 25If you want to return the printer to the factorydefault settings, turn the power on while holdingdown the MODE/Exit and SEL buttons, all menuset
E – 26SpecificationsPrint method Impact dot matrixPrinthead 24 pin (ML390FB)9 pin (ML320FB)Print speedUtility 270 cps at 12 cpi(ML390FB)250 cps at 12
E – 27Electrical characteristicsVoltage 230V AC(+6%-14%).240V AC(±10%).Frequency 50/60Hz ±2%.Data interface Centronics parallelstandard.RS232C serial
E – 28Cut sheetsWidth 90mm to 304.8mm.Length 70mm to 420mm.Single partWeight 12 to 41lb.Thickness 0.051mm to 0.196mm.Multipart*Weight Paper: 10 to 12l
E – 2Note to CustomersEvery effort has been made to ensure that theinformation in this manual is complete, accurateand up-to-date. Oki assumes no resp
E – 3Important Safety InstructionsYour printer has been carefully designed to performsafely and reliably. However, as with all electricalequipment cer
E – 4Important Wiring InstructionsThe wires in the mains lead are coloured inaccordance with the following code:Green and Yellow EarthBlue NeutralBrow
E – 5Installing Your PrinterPrior to unpacking the printer, find a flat, sturdysurface to place it on, for example, a desk, printerstand, etc. Gently
E – 6PreliminariesBefore plugging in the printer, follow these steps toinstall your printer.1. Hold both sides of the access cover and lift up.There i
E – 72. Next install the sheet stacker.Put the stud of one of the stacker’s legs into thehole at the end of the rear vent. Gently press theother leg u
E – 85. Turn the power switch off.Important: Make sure the socket is earthed. Do notuse an adapter because it will defeat the earthing.!
Commentaires sur ces manuels